Flow control valve is a valve that controls fluid flow by varying its cross section or length, without the negative feedback function of flow, the speed instability caused by load change can not be compensated. It is only used for occasions where the load changes little or the speed stability is not high. Whatever your application is, we have a dependable flow control valve series that will accommodate your most demanding application.
2L Solenoid Valve Feature: Indirect acting(Internal pilot) and normally closed type 2/2 way solenoid valve. Its high sensibility allows it to change direction quickly. It is compact, small size and light weight. It is easy to install and dismantle. The valve body is made of SUS304. Its coil has a Heat resistance classification of Class H. The standard seal material is PTFE(Teflon) which is suitable for a variety of working medium such as water with high temperature and vapour. The protection class of the coil is IP65 and there is a choice for grommet or terminal electrical entry. Airsky 2L Solenoid valve equivalent to Airtac 2L, with the same appearance.
2KL Solenoid Fluid Control Valve Discription: Direct acting and normally opened type 2/2 way solenoid valve. Its high sensibility allows it to change direction quickly; It has wide pressure range, including standard high pressure (H) to choose from; It is compact, small size and light weight. It is easy to install and dismantle; The valve body is made of SUS304 . Its coil has a Heat resistance classification of Class H. The standard seal material is PTFE(Teflon) which is suitable for a variety of working medium such as water with high temperature and vapour. 2KL solenoid valve equivalent to AIRTAC 2KL valve, with the same appearance.
2J Solenoid Valve installation & uses: Before using, please verify that if the working status of product is identical with data in catalogue, and it should not exceed the limits. Before the pressure releasing and cooling of system, no maintenance, examination and installation of product should be conducted. For the normally-closed-type , when its valve is disassembled, due to the pre-pressure of the relatively large spring power in controller, the “1” hole should be opened for ventilation in advance so to make sure the piston could be completely moved to the position, then rotate the screw thread between the valve and the connection bar, direct rotation is forbidden, otherwise the disassembling would not be conducted in result of the scuffing of screw thread. If maintenance of actuator part is needed, special tools should be used for disassembling and installation, while disassembling, the loading spring could cause damage. If the customer can not conduct the maintenance, please return the valve to manufacturer for maintenance. Airsky 2J solenoid fluid control valve equivalent to AIRTAC 2J, with the same appearance.
2S Solenoid Valve Uses: Before installing, be sure the valve hasn’t been damaged via transportation. The coil must be pure vertical, the inlet and outlet on body must be horizontal. it’s suggested to use the medium lubricated by 40μm filter element. Be aware of the flow direction and port size. Please notice whether the installation condition accords with technical requirements (such as “voltage”,“actuation frequency”, “working pressure” and “scope of application temperature”), then the equipment can be installed and used. Take measure to avoid vibration and frozen. Before using the fittings and tubes make sure they are clean. When connecting tofittings, be sure the PTFE Thread Seal Tape is used correctly. 2S solenoid valve equivalent to Airtac 2S fluid control valve , with the same appearance.
Airsky’s GRO flow control valve is equivalent to Festo GRO. GRO flow control valve can change the size of local resistance by changing the flow area of the orifice or the length of the circulation channel, thereby achieving the control of the flow and thus changing the movement speed of the actuator.
The VPCF porportional flow control valve satisfies the highest requirements in terms of dynamic response, repetition accuracy and characteristic curve linearity. Extremely short cycle times mean that unit numbers can be increased and therefore costs can be cut substantially.
The function combination consists of a GRXA flow control valve and a piloted non-return valve. Exhaust air flow control is active as long as a pilot signal from pneumatic connection 21 is applied. If no pilot signal is applied, the valve shuts off the exhaust air. The compressed air flows unthrottled through the non-return valve in the supply air direction.
GRLA Flow Control Valve: Flow control or one-way flow control valves regulate the piston speed of pneumatic drives during advance and return strokes. This is done through suitable restriction of the flow rate of compressed air in exhaust air or supply air direction. With the one-way flow control valve GRXA or GRXZ, the flow control function works in one direction only (exhaust air or supply air); the non-return function works in the opposite direction. With the flow control valve GRLO, the flow control function is active in both directions.